Power Point® Nozzles

 
 
 
 
 
 
 
Power Point Nozzles

MDi’s internally heated Power Point® nozzles are machined from a single piece of H-13 steel, eliminating the stresses and leakage that can occur with multiple-piece nozzle body constructions. MDi’s exclusive design prevents nozzle leakage while it provides a uniform heat profile. The replaceable tip configurations include Direct Gate, Edge Gate, Full Body, Valve Gate, Extended Tip, and Sprue Type.

MDi also offers customized solutions to address all your special needs. Please contact us to further assist you.

Product Features

Internally Heated: Uniform heat profile due to the resistance wire with a pre-determined wattage distribution across the nozzle body

Ceramic Insulator: Compacted near its theoretical limits, it ensures the highest heat transfer rate, and maximizes heater life.

Thermocouple well: A removable thermocouple can be inserted into a provided thermowell, located at the tip for a more accurate melt temperature reading.

Repairable leads: The leads can be repaired if they are physically damaged.

Replaceable tips: The replaceable tip configurations include direct gate, edge gate, full body, valve gate, extended tip and sprue type.

Power Point® Series

The Power Point® nozzle series is a result of MDI's continuous effort to improve its hot runner system performance. Based on the patented iinternally heated design of our Equatemp® Hot Sprue Bushings, the Power Point® line provides the customer with: both temperature uniformity and various gating options that include; topless (direct), sprue, full body, extended tip, multi-tip, hot edge and valve.


Extended Tip

The extra reach on this tip allows for precision gates in tight locations

BC75

Topless Tip

The most common tip which is designed for excellent cosmetic gates

PS75T

Full Body

The gate geometry is machined in the end cap while allowing good gate vestige

PS75F

Sprue Type

A replaceable tip for feeding runners

PS75S

Through Tip

A replaceable tip for good heat transfer with a through flow

PS75R

Special Applications

The Flat and Mini nozzle series are good for close pitch applications. Our Flat nozzles offers a flat body while our Mini nozzles offer a small body diameter making both a perfect solution for tight locations. Both series are available in Extended, Topless, Full Body, and Sprue style configurations. The TR Nozzles Series is used for special applications, with Angled Tip or Offset Tip option.

MDi also offers customized solutions to address all your special needs. Please contact us to further assist you.



Internally Heated vs. Externally Heated Nozzles


Why internally heated nozzles make more economic sense

Anyone who designs, builds, runs or repairs injection molds knows the importance of having optimum control over heat profiles to reduce material waste and maintenance downtime due to nozzle leaks or just poorly molded parts.

Eliminating the risks of overheating and leaking is therefore a much sought after objective, and it makes economic sense to consider incorporating internally heated Hot Runner nozzles or molding Machine Nozzles into the mold design or production process because they save money.

One key reason internally heated nozzles save money is because they are 100 percent sealed. Plastic material cannot leak out and damage wires in the channels or nearby nozzles, whereas, with traditional externally heated nozzles, leaking and system damage can and does occur.

For example, if one externally heated nozzle leaks in a Hot Runner system, more often than not the leaked plastic will follow the wire channels and flood them, causing all of the nozzles and channels to become one big plastic mess. It can be an expensive repair job if the entire heating system is affected.

In addition, in Hot Runner systems using internally heated nozzles, spare parts are rarely, if ever, required because the nozzles do not leak. To emphasize this point, a major multinational OEM that manufactures caps and closures has employed more than 200 internally heated, multi-cavity Hot Runner systems for more than 14 years and, because the company has seen firsthand the benefits of the internally heated nozzle, it does not stock spare parts. That’s true savings.

Because a Hot Runner system is often a large part of the overall cost of a mold, some people stress about the warranty of the system, but they don’t consider the frequency of burnouts or other issues that can cost dearly in downtime. Utilizing internally heated Hot Runner nozzles alleviates the stress because they are virtually fail-proof compared to traditional, externally heated systems. They are like an insurance policy against downtime and replacement part costs.

In most cases, internally heated Hot Runner nozzles can be retrofitted on existing Hot Runner systems. It should also be noted that they work well with hot halves available on the market that offer the same features.

The Internal Difference

With an externally heated nozzle, the sensitive parts of the heating system—such as the thermocouple, heating coil, sleeve, etc.—are located on the outside of the nozzle body. As the coil is heated it expands, causing a gap between itself and the nozzle body so that it cannot touch the nozzle body uniformly. Because of this, the coil must be heated at a higher temperature to properly heat the plastic. Not only is there a risk of heating unevenly, but the higher temperature also means there is a risk of overheating and burning out the coil (heater failure).

This is not so with an internally heated nozzle. Because the insulation around the heating wire is solidly compacted to maximum density it eliminates any air voids around the resistance wire and surrounding nozzle bore. The heater inside the nozzle is an integral part of the body, so it resists burning out and contributes to more efficient heating. How? The heater element is able to run cooler due to the highly dense insulator, which carries away heat produced on the surface of the resistance wire when the heater is energized. So not only does it run more efficiently, it also helps prolong the heater life.

Another notable benefit of internally heated nozzles is the location of the thermocouple. The thermocouple and the heating element are located much closer to the gate, at the end of the nozzle, so they deliver heat at a very precise temperature. The result is a better heat profile and more controlled melt temperature and, therefore, better molded part quality. With externally heated nozzles, the nozzle may be heated properly, but there is a risk that the nozzle tip is not because the thermocouple stops short of the gate. Add to that the structure of the external coil and temperature profiles may be anything but consistent.

Granted, if the heating coil on an externally heated nozzle burns out, it can conveniently be replaced without removing the mold from the press—as long as no leaking has occurred. This is not possible with an internally heated nozzle, but it’s clear the benefits outweigh the slim chance of the heating element burning out and, like other systems, nozzle tips and seals are replaceable at the molding machine.

Ease of Maintenance

While there is little, if any, need for replacement parts when using an internally heated Hot Runner nozzle, in the rare instance that the thermocouple does fail, it can be quickly and easily changed out while the heating element remains intact—definitely a savings in time and cost. This is not possible with some styles of externally heated nozzles, as too often the entire coil must also be replaced.

Summary

Whether one is looking to cut costs, reduce material waste and downtime or produce more quality parts, internally heated Hot Runner nozzles and Machine Nozzles offer a clear-cut solution.

Hot Runner Systems made in U.S.A

MDi is a world-leading American manufacturer of Hot Runner systems and components with the capability to develop custom and innovative solutions for plastics Injection Molding. Established in 1984, MDi continues to offer experience in the design and manufacturing of complete, internally heated and balanced precision Hot Runner systems, Valve Gate systems, Sprue Bushings, Molding Machine nozzles, Filters, and MDi's unique system products and controls. All of our components are in-house designed and manufactured in our facility at St. Charles, IL, with a focus on quality and reliability.